Skip to content

Circle Functions

Circle with given centre and radius

Icon1 Draw toolbar
Draw menu > Circle with given centre and radius

This function enables the construction of one or more circles by entering the radii.

Circle property bar

circle-by-radius
The line type, line colour, radii and the circle's reference point can be specified in the property bar.
In ELITECAD Architecture the renovation planning state can be selected.

Radius

Up to 10 radii can be entered separated by commas.

Reference point

circle-with-centre-radius-ref-point-selection
The reference point determines which point the circle is attached to the crosshair.

aux_circ_ref5_ aux_circ_ref4_
circle-with-centre-radius-ref-point-middle-sample circle-with-centre-radius-ref-point-edge-sample

Circle by centre

Icon1 Draw toolbar
Draw menu > Circle by centre

This function creates a circle by specifying the centre point as well as a point on the circle's circumference. The circle can also be established tangentially to an element (drawing line, help line or line, curve).

Circle property bar

circle-by-centre
The line type and line colour can be selected from the properties bar.
In ELITECAD Architecture the renovation planning state can be selected.

Through point Tangential to element
circle-by-centre-by-point circle-by-centre-by-element
Tip

You can see which capture mode is active by the appearance of the crosshair. This means you can see whether a circle will be created tangential to an element or straight through a point. As long as you position the element with the element mode, the circle will be generated tangential to the element.

Circle by 3 points or tangents

Icon1 Draw toolbar
Draw menu > Circle by 3 points or tangents

This function enables the construction of a circle, which is specified by three "locations". These "locations" can be either free points or tangential points.

Options

By 3 Points Mixed By tangents
circle-by-3-pts1 circle-by-3-pts2 circle-by-3-pts3

After activating the function, the points or elements to which the circle needs to be tangential must be selected one by one.

Cursor position

The direction changes depending on the cursor's position over the crosshair.

Cursor above crosshair Cursor below crosshair
circle-by-3-pts-cursor-position1 circle-by-3-pts-cursor-position2

Circle by radius

Icon1 Draw toolbar
Draw menu > Circle by radius

This function creates a circle with the radius value specified in the property bar and then prompts for two more points or tangential elements.

Tip

circle-by-radius
The radii of circles can be modified later by selecting the circle.

Options:

By 2 points mixed by tangents
circle-by-radius1 circle-by-radius2 circle-by-radius3

When the function is activated, the property bar opens and you can specify the radii. The points or elements to which the circle needs to be tangential must then be selected one by one.

Cursor position:

The direction changes depending on the cursor's position over the crosshair.

Cursor above crosshair Cursor below crosshair
circle-by-3-pts-cursor-position1 circle-by-3-pts-cursor-position2

Curve by 3 points

Icon1 Draw toolbar
Draw menu > Curve by 3 points

This function creates a curve through a given start point, point on the circumference and end point.
While drawing a curve the entry mode can be changed in the input assistant. Three options are available:
Icon1 Curve by 3 points
Icon1 Curve by centre point
Icon1 Curve by tangent

Curve property bar

circle-by-3-points
The line type and line colour can be selected from the property bar. The curve radius and angle are displayed when editing.
In ELITECAD Architecture the renovation planning state can be selected.

Curve over angle, direction and centre point

Icon1 Draw toolbar
Draw menu > Curve over angle

This function enables a curve through a given start point, angle and the curve's centre point.

Curve property bar

circle-by-centre-point
The line type and line colour can be selected from the property bar. The curve radius and angle are displayed when editing.
In ELITECAD Architecture the renovation planning state can be selected.

Ellipse

Icon1 Geometry toolbar
Draw menu > Geometry > Ellipse

This function is used to create an ellipse.
Create an ellipse by inputting two vertices on an axis and clicking on a third.

Ellipse property bar

circle-by-ellipse
The line type and line colour can be selected from the property bar.
In ELITECAD Architecture the renovation planning state can be selected.

Spline

Icon1 Geometry toolbar
Draw menu > Geometry > Spline

This function enables the creation of a smooth interpolation curve with a random number of points (cubic splines).

After activating the function, you can specify the points of the polygon and to end the spline, select the last point a second time. In this case, the curve is incomplete and you will be prompted to enter an inclination angle at the start and end points.

Spline property bar

circle-by-spline
The line type and line colour can be selected from the property bar.
In ELITECAD Architecture the renovation planning state can be selected.

Revision cloud

Icon1 Geometry toolbar
Draw menu > Geometry > Revision cloud

The revision cloud is a 2D element, which usually is used to add annotations about changes to the model.
After activating the function, you can specify the points of the revision cloud. By closing the polygon or in selecting the last point a second time, the point input is terminated.

Revision cloud property bar

circle-by-revision-cloud
The property bar becomes visible as soon as the REVISION CLOUD function is started or an existing REVISION CLOUD is selected. The line type and line colour can be selected from the property bar.
In ELITECAD Architecture the renovation planning state can be selected.

Bulge length

Icon1
The bulge can be oriented inward or outward.

Average bulge length

dist_x_
The average bulge length defines the average length of the arcs.